Wenn man die Wasserpumpe für die Nacht ausschaltet kann man aber doch die Wasserspühlung der Toilette nicht benutzen. Ich beneide Euch um Euren durchgehenden Nachtschlaf.
Gruß
Tom
Wenn man die Wasserpumpe für die Nacht ausschaltet kann man aber doch die Wasserspühlung der Toilette nicht benutzen. Ich beneide Euch um Euren durchgehenden Nachtschlaf.
Gruß
Tom
Das stimmt - braucht ne Clesana aber auch gar nicht
Wenn man die Wasserpumpe für die Nacht ausschaltet kann man aber doch die Wasserspühlung der Toilette nicht benutzen. Ich beneide Euch um Euren durchgehenden Nachtschlaf.
Gruß
Tom
Hallo Tom,
des nachts kann man die Pumpe ja zu einem Spülvorgang mal einschalten.
Ich hatte dieses Jahr, nach dem Winterlager, beim ersten Testlauf der Wasserversorgung, dass Filtergehäuse nicht wieder fest verschraubt. Man wundert sich wie schnell und wie viel Wasser sich in der Heckgarage sammelt. Gott sei Dank stand mein Womo mit dem Heck bergab, sodaß sich das Wasser nur im hinteren Bereich der Heckgarage sammelte. Trotzdem mußte ich die Garage komplett leer räumen und meinen schönen Bodenbelag usw. trocknen. Das passierte natürlich als das Womo abfahrbereit fertig war. Man hatte ich eine Laune.
Gruß Martin
Hab mir jetzt aufgrund dieser Diskussion nen Feuchtigkeitssensor zugelegt den ich natürlich im HA (HomeAssistant - ja ich weiss nerviges Thema) einbinden kann und mich ggbfs. via Telegram alarmiert
Nachdem auch wir eine Undichtigkeit in unserem Wasserkreislauf nicht bemerkt haben, haben wir nun unsere Wasserpumpe auf Bewegungssensoren umgebaut. An jeder Wasserentnahme Stelle gibt jetzt der Bewegungssensor den Strom auf die Pumpe frei. Solang man sich im Erfassungsbereich aufhält.
Ist man nicht mehr im Erfassungsbereich schaltet die Stromzufuhr nach 5Sekunden ab.Die Sensoren die hier verwendet wurden kann man auf 5 s bis 30 Minuten einstellen
Nun kann man sicher sein ,das wenn man nicht im Wohnmobil ist, das auch dann kein Wasser läuft.
Gib Mal Bewegungssensor hier ein da kommt der ganze Beitrag und wie die Sensoren aus sehen
Hallo, bei uns läuft die Wasserpumpe wenn wir unterwegs sind.
Grüße aus dem Allgäu
Rhomas
Hallo in die Runde der Freunde der Druckwasserpumpen,
was waren doch oder sind noch die Tauchpumpen schön, Druck nur, wenn der Wasserhahnschalter schaltet .
Ich bemühe mich, auch immer daran zu denken, wenn wir das Mobil verlassen, den Taster zu drücken. Man muss eh an Allerlei denken, Fenster zu, Dachluken wegen Regen, Garage- und andere Bodenklappen verriegelt, Tür verriegeln, Alarmanlage ggf. (je nach Gegend) ... , da kommt es nun darauf für mich auch nicht mehr an. Und noch klappt´s ja einigermaßen . Wie wir letztens beim Regensensor für die Dach-Hekis gemerkt haben, hat die liebe Elektronik durchaus auch mal ihre Tücken.
Kleine Bitte noch an einen Mod: Dem Wasser in der Überschrift bitte noch ein zweites "s" gönnen .
Beste Grüße
Dieter
Kleine Bitte noch an einen Mod: Dem Wasser in der Überschrift bitte noch ein zweites "s" gönnen .
Wie immer … kleine Wunder werden sofort erledigt.
VG, Thomas
Wir schalten die Wasserpumpe immer während der Fahrt aus und achten beide penibel drauf. Während der Fahrt ist m. E. die Wahrscheinlichkeit aufgrund von Vibrationen, Schlaglöchern etc. am höchsten, dass sich eine Verbindung löst, Risse entstehen oder etwas am Wassersystem kaputt geht.
Während der Fahrt würden wir das nicht hören.
Theoretisch schaltet unser Fahrzeug die Pumpe nach x-Minuten automatisch ab, jedoch m. E. nur bei Dauerbetrieb! Hätten wir also eine kleinere undichte Stelle, so schlägt diese Schutzfunktion evtl. nicht zu und wir hätten mehrere hundert Liter im Keller verteilt.
Ich habe gerade eine automatische Abschaltung durch einen Eltako Aktor eingebaut.
Statt Bewegungsmelder gibt es kleine versteckte 12mm Taster in Küche, Bad und Keller. Einmal kurz drauf drücken, die Wasserpumpe ist für eine frei einstellbare Zeit aktiv und wird danach automatisch abgeschaltet. Materialeinsatz ca. 80,- Euro und ca. 90 Minuten Arbeit. Hätte ich es mit den Eltako Funkschaltern realisiert, wäre es schneller gegangen, die waren mir dann aber doch zu groß und die Batterien wären nach Murphy‘s Law dann leer, wenn es gerade nicht passt.
Habe mir eine Wapu-Schaltung nachgebaut und ist jetzt über 1 Jahr im Einsatz. Bin damit voll zufrieden und brauche mich nicht mehr ums abschalten zu kümmern.
Für diese Schaltung gibt es schon einen Beitrag.
linertreff.com/board/thread/8924/Grüße Xaver
Meinen Respekt für den, der sich das hat einfallen lassen! Für einen Laien ist das alerdings nur schwer nachzubauen. Der Vorteil der Eltako Lösung brauchst Du nur eine 12V legen, und den Aktor in die Stromleitung der Wasserpunpe hängen, das bekommt jeder hin. Dann kann man entscheiden ob Funktaster, Bewegungsmelder oder verkabelte Taster zum Einsatz kommen.
Da unsere Elektrik beim Stillstand ausgeschaltet wird, läuft die Pumpe dann auch nicht.
Unterwegs ist sie immer an und bleibt es auch.
In letzten 30 Jahren habe ich von keinen Problemen mit selbstanlaufender Pumpe gehört.
Extra Bewegungssensoren wäre mir zu viel Arbeit
Naja sie läuft ja auch nur an bei
a) Leck wenn Druckwasserpumpe
b) defektem Microschalter bei Campingwasserhähnen
Also relativ selten. Bei b) würde ich mir keine Sorgen machen, da das Wasser ja in den Abwassertank läuft. Das Thema dreht sich hier um a) und da kann die Leckage auch im Unterboden sein... Deshalb diese Diskussion
Zum Glück hatten wir noch kein Leck.
Liegt vielleicht auch dran das die Fahrzeuge nicht so alt bei uns werden.
Beim Einbau vom neuen Wasserhahn hatte ich Wasser im doppelten Boden.
Aufgewischt und fertig.
Hallo und guten Abend,
ist zwar schon ein paar Jahre her. Bei unserem damaligen, neuen Flair hatte sich eine Schlauchschelle hinter der Dusche geringfügig gelockert, die Pumpe sprang in unregelmäßigen Abständen an und das Wasser tropfte durch die undichte Stelle. Glücklicherweise waren wir im Wohnmobil. Seitdem wird die Pumpe bei Nichanwesenheit und auch nachts ausgestellt.
Tja, so unterschiedlich wird das gehandhabt. Wenn wir Anfang Oktober wegfahren, wird die Pumpe angestellt und wenn wir nach ca. 7 - 8 Monaten in Spanien zurück kommen, ausgemacht. Das ein Schlauch abspringt, ist doch sehr unwahrscheinlich, der wird vorher undicht und die Pumpe springt öfter an und man kann sich auf die Fehlersuche machen. Seit einiger Zeit werden auch keine Schlauchschellen mehr verbaut, sondern es wird gecrimpt. Da kann sich dann nichts lösen. In der Regel sind es Undichtigkeiten, Alde Warmwasserabgang tut sich da hervor oder irgendwo ist ein Haarriss im Kunststoff oder der Frost hat einen Wasserhahn beschädigt. Das merkt man immer am häufigen einschalten der Pumpe und grosse Mengen treten da nicht aus. Insofern bin ich da sehr entspannt. Fazit: jeder muss da für sich Entscheiden was für ihn richtig ist.
Hallo Ludwig,
falls Du meinen Beitrag kommentierst, lies mal bitte genau, was ich geschrieben habe. Falls ich nicht gemeint bin, sorry.
Hallo, das war eher allgemein gedacht. Unser Morelo von 2018 und neuere Phoenix haben keine Schlauchschellen mehr sondern gequetschte Schellen. Da löst sich nix.
Eine gequetschte Schelle hat sich bei mir gelöst.